1:32nd scale Hansa-Brandenburg W.12
+2
JP
Mike
6 participants
Page 1 sur 2
Page 1 sur 2 • 1, 2
1:32nd scale Hansa-Brandenburg W.12
The 'Wingnut Wings' model of the Hansa-Brandenburg W12, Serial No.1184 (C3MG) as flown by Fl.Mt. Urban and Lt. Ehrhardt of C-Staffel, Zeebrugge, during December 1917.
This aircraft was part of a three aircraft patrol that shot down the British Naval airship C27, killing all five of the crew
Mike
This aircraft was part of a three aircraft patrol that shot down the British Naval airship C27, killing all five of the crew
Mike
Dernière édition par Mike le Lun 24 Juil - 19:41, édité 1 fois
Re: 1:32nd scale Hansa-Brandenburg W.12
Hi all
The engine is complete apart from adding control rods once the engine is fitted into the fuselage.
I've added a few changes to the kit supplied engine:
Nickel-Silver push rods of 0.4 mm diameter.
Rear coolant pipe from 0.5 mm diameter lead wire.
Fuel filter pipes from 0.3 mm diameter copper wire.
Throttle control return spring from 0.125 mm diameter copper wire.
Ignition lead support tubes from shaped Brass tube.
Ignition leads from 'EZ' black line (Fine).
Fuel priming levers from 0.2 and 0.4 mm diameter Brass tube and Nickel-Silver rod.
Crankcase vent ports from 'RB Productions' photo-etch grill
Mike
The engine is complete apart from adding control rods once the engine is fitted into the fuselage.
I've added a few changes to the kit supplied engine:
Nickel-Silver push rods of 0.4 mm diameter.
Rear coolant pipe from 0.5 mm diameter lead wire.
Fuel filter pipes from 0.3 mm diameter copper wire.
Throttle control return spring from 0.125 mm diameter copper wire.
Ignition lead support tubes from shaped Brass tube.
Ignition leads from 'EZ' black line (Fine).
Fuel priming levers from 0.2 and 0.4 mm diameter Brass tube and Nickel-Silver rod.
Crankcase vent ports from 'RB Productions' photo-etch grill
Mike
CRICKEY aime ce message
Re: 1:32nd scale Hansa-Brandenburg W.12
Hi all
The fuselage is ready to be closed up.
I've carried out a few enhancements to the cockpit:
Rudder control pulleys drilled and control cables added (0.08 mm diameter mono-filament and blackened 0.4 mm diameter Nickel-Silver tube).
Elevator control levers drilled and control cables added (0.08 mm diameter mono-filament and blackened 0.4 mm diameter Nickel-Silver tube).
Aileron control cables (photo-etch) replaced with 0.08 mm diameter mono-filament and 'Proper Plane' resin turnbuckles.
Observers seat and map shelf side stays added from blackened 0.4 mm diameter Nickel-Silver tube.
Lead wire 0.4 mm diameter added for the fuel tank hand pressurizing pump.
Copper wire 0.125 mm diameter wrapped around the pilot control wheel to represent hand grip.
Nickel-silver 0.4 mm diameter tube used for the throttle quadrant to engine carburetor control rod
Mike
The fuselage is ready to be closed up.
I've carried out a few enhancements to the cockpit:
Rudder control pulleys drilled and control cables added (0.08 mm diameter mono-filament and blackened 0.4 mm diameter Nickel-Silver tube).
Elevator control levers drilled and control cables added (0.08 mm diameter mono-filament and blackened 0.4 mm diameter Nickel-Silver tube).
Aileron control cables (photo-etch) replaced with 0.08 mm diameter mono-filament and 'Proper Plane' resin turnbuckles.
Observers seat and map shelf side stays added from blackened 0.4 mm diameter Nickel-Silver tube.
Lead wire 0.4 mm diameter added for the fuel tank hand pressurizing pump.
Copper wire 0.125 mm diameter wrapped around the pilot control wheel to represent hand grip.
Nickel-silver 0.4 mm diameter tube used for the throttle quadrant to engine carburetor control rod
Mike
Squirell50 et CRICKEY aiment ce message
Re: 1:32nd scale Hansa-Brandenburg W.12
Very beautiful job!!!
Bonne suite de montage..
Bonne suite de montage..
JP- Messages : 3636
Date d'inscription : 13/05/2018
Age : 62
Localisation : Ambutrix
Re: 1:32nd scale Hansa-Brandenburg W.12
c'est joli
CRICKEY- Messages : 419
Date d'inscription : 02/02/2022
Age : 55
Localisation : Essone
dakota59- Messages : 1064
Date d'inscription : 20/03/2019
Age : 60
Localisation : 59250 halluin
Re: 1:32nd scale Hansa-Brandenburg W.12
Hi all,
I've replaced the kit supplied Spandau and Parabellum machine guns with modified 'Gaspatch' weapons.
The fuselage and other parts were primed then airbrushed with 'Tamiya' Grey (XF53).
The wings, ailerons and elevator were primed white and pre-shaded with 'Tamiya' Smoke (X19) prior to decal application (Aviattic),
Mike
I've replaced the kit supplied Spandau and Parabellum machine guns with modified 'Gaspatch' weapons.
The fuselage and other parts were primed then airbrushed with 'Tamiya' Grey (XF53).
The wings, ailerons and elevator were primed white and pre-shaded with 'Tamiya' Smoke (X19) prior to decal application (Aviattic),
Mike
Re: 1:32nd scale Hansa-Brandenburg W.12
It's very good and beautiful!!!
JP- Messages : 3636
Date d'inscription : 13/05/2018
Age : 62
Localisation : Ambutrix
Re: 1:32nd scale Hansa-Brandenburg W.12
Hi Mike,
Very nice subject and work !
I shall follow this build with interest.
All the best,
Lorenzo
Very nice subject and work !
I shall follow this build with interest.
All the best,
Lorenzo
Veneto Vittorio- Messages : 133
Date d'inscription : 27/09/2022
Age : 58
Localisation : Gallia Narbonensis
Re: 1:32nd scale Hansa-Brandenburg W.12
Hi all,
The fuselage was mottled with two slightly different shades of grey to give a weathered look to the wood surface.
The kit decals were replaced with 'Aviattic' decals as being more representative of the Lozenge colours.
The darker lozenge was decal over a grey base coat, to represent the darker linen effect over wood surfaces and upper wing auxiliary fuel tank.
The lighter linen shade was over white base coat.
The direction of the lozenge on the ailerons and elevator are different to the rest of the aircraft lozenge, as on the actual aircraft.
Still more detail painting and subsequent weathering to be done before assembly,
Mike
The fuselage was mottled with two slightly different shades of grey to give a weathered look to the wood surface.
The kit decals were replaced with 'Aviattic' decals as being more representative of the Lozenge colours.
The darker lozenge was decal over a grey base coat, to represent the darker linen effect over wood surfaces and upper wing auxiliary fuel tank.
The lighter linen shade was over white base coat.
The direction of the lozenge on the ailerons and elevator are different to the rest of the aircraft lozenge, as on the actual aircraft.
Still more detail painting and subsequent weathering to be done before assembly,
Mike
Squirell50 aime ce message
Re: 1:32nd scale Hansa-Brandenburg W.12
So beautiful!!!
JP- Messages : 3636
Date d'inscription : 13/05/2018
Age : 62
Localisation : Ambutrix
Re: 1:32nd scale Hansa-Brandenburg W.12
Hi all,
The basic fuselage and lower wings assembled.
The two 'Spandau' machine guns and associated kit parts were replaced with slightly modified 'Gaspatch' weapons.
Still a lot of detail and weathering to do before full construction can start,
Mike
The basic fuselage and lower wings assembled.
The two 'Spandau' machine guns and associated kit parts were replaced with slightly modified 'Gaspatch' weapons.
Still a lot of detail and weathering to do before full construction can start,
Mike
Squirell50 aime ce message
Re: 1:32nd scale Hansa-Brandenburg W.12
It's very beautiful...
JP- Messages : 3636
Date d'inscription : 13/05/2018
Age : 62
Localisation : Ambutrix
Re: 1:32nd scale Hansa-Brandenburg W.12
Hi all,
I got carried away on the build and forgot to post later updates.
Apart from fitting the propeller the basic aircraft is finished.
I still have the figures and display base to do so still a bit to go yet,
Mike
I got carried away on the build and forgot to post later updates.
Apart from fitting the propeller the basic aircraft is finished.
I still have the figures and display base to do so still a bit to go yet,
Mike
Squirell50 et CRICKEY aiment ce message
Re: 1:32nd scale Hansa-Brandenburg W.12
Il est magnifique!!!!
Bravo..
Bravo..
JP- Messages : 3636
Date d'inscription : 13/05/2018
Age : 62
Localisation : Ambutrix
Re: 1:32nd scale Hansa-Brandenburg W.12
super montage bien soignée et puis de belles peintures, le choix des couleurs la méthode, j'aime beaucoup
CRICKEY- Messages : 419
Date d'inscription : 02/02/2022
Age : 55
Localisation : Essone
Re: 1:32nd scale Hansa-Brandenburg W.12
Tes beau travail. Peut-être les nuances sous les decals auraient pu elles être plus fortes?
Re: 1:32nd scale Hansa-Brandenburg W.12
Xan a écrit:Tes beau travail. Peut-être les nuances sous les decals auraient pu elles être plus fortes?
Salut Xan
Oui, ils ne se sont pas présentés autant que prévu cette fois
Mike
Re: 1:32nd scale Hansa-Brandenburg W.12
Hi all,
Here's the Hansa-Brandenburg W.12, Serial No.1184 (C3MG) as flown by Fl.Mt. Urban and Lt. Ehrhardt of C-Staffel, Zeebrugge, during December 1917.
As usual, a fully detailed build log, which includes all materials, modifications, rigging etc for this build can be downloaded from the 'Logs' page on my site.
https://mikesww1aircraftmodels.com/
Thanks for your comments and support throughout this build,
Mike
Here's the Hansa-Brandenburg W.12, Serial No.1184 (C3MG) as flown by Fl.Mt. Urban and Lt. Ehrhardt of C-Staffel, Zeebrugge, during December 1917.
As usual, a fully detailed build log, which includes all materials, modifications, rigging etc for this build can be downloaded from the 'Logs' page on my site.
https://mikesww1aircraftmodels.com/
Thanks for your comments and support throughout this build,
Mike
Squirell50 et CRICKEY aiment ce message
Re: 1:32nd scale Hansa-Brandenburg W.12
Hi Mike,
What a beautiful work, it’s a true piece of art! The figures are also are also very well painted.
So, I went to visit your website and downloaded the pdf dedicated to your BE2C assembly. I will definitely find ideas and inspiration for mine in 1/48 scale.
Congratulations again for your Hansa-Brandenburg W. 12.
What a beautiful work, it’s a true piece of art! The figures are also are also very well painted.
So, I went to visit your website and downloaded the pdf dedicated to your BE2C assembly. I will definitely find ideas and inspiration for mine in 1/48 scale.
Congratulations again for your Hansa-Brandenburg W. 12.
Veneto Vittorio- Messages : 133
Date d'inscription : 27/09/2022
Age : 58
Localisation : Gallia Narbonensis
Re: 1:32nd scale Hansa-Brandenburg W.12
All is so marvellous!!!
Bravo pour cette réalisation..
Bravo pour cette réalisation..
JP- Messages : 3636
Date d'inscription : 13/05/2018
Age : 62
Localisation : Ambutrix
Page 1 sur 2 • 1, 2
Sujets similaires
» 1:32nd scale Bristol F.2b
» 1:32nd scale Hanriot HD.1
» hansa Brandenburg W.33
» 1:32nd scale Macchi M.5
» 1:32nd scale Halberstadt D.II
» 1:32nd scale Hanriot HD.1
» hansa Brandenburg W.33
» 1:32nd scale Macchi M.5
» 1:32nd scale Halberstadt D.II
Page 1 sur 2
Permission de ce forum:
Vous ne pouvez pas répondre aux sujets dans ce forum
|
|